
Komatsu Idler D155AX-3
Tüüp: BULDOOSER
Mudel: D155AX-3
IDLER/IDLER RATAS
Kaubamärk: KOMATSU
Tüüp: BULDOOSER
Mudel: D155AX-3
IDLER/IDLER RATAS
Viis viis säilitada ja säilitada the buldooser( 2~5 )
2. Hoia tühikäik asend tsentreeritud
äpardus of the guide wheel on a tõsine impact on other walking mehhanism osad. Seega, reguleerimine the gap vahel the guide plate of the guide wheel and the crawler frame is the key to prolong the service life of the walking mechanism. During adjustment, use the tihend between the guide plate and the camping to correct. If the gap is large, remove the tihend; If the clearance is small, add shims. The standard clearance of buldooser maintenance method is {{{{{}}}}}.5 ~ 1.0}mm, and the maximum allowable clearance is 3.0mm. Turn over the track pin and the pin sleeve at an appropriate time.
Ajal the wear process of the track pin and the pin sleeve, the track pitch is järk-järgult pikenenud, tulemuseks in poor haardumine vahel ajam ratas ja the pin sleeve, resulting in damage of the pin sleeve and ebanormaalne kulumine of the drive hammas pind, mis tahe põhjus jaht, slapping and impact, ja suuresti lühenda teenus elu of the traveling mehhanism. Millal pigi ei saa taastuda abil reguleerimine the tension, it on vajalik to turn over the track and pin sleeve to get the correct track pitch. There are two method to determine the turnover of track pin and pin sleeve on site: one method is to check and determine that the track pitch is pikenenud by 3mm; Another method is to check that the outer diameter of the pin sleeve on kulunud poolt 3mm.
3. Poldid ja mutrid peab pingutama sisse aeg
Millal polt of the traveling mehhanism on lahti, it on lihtne to break or lose, põhjus a seeria of vead. The following poldid tuleb kontrollida for rutiin hooldus: kinnitus poldid of supporting roller and supporting roller, mounting poldid of driving hammasratas plokk, paigaldus poldid of track shoe, paigaldus poldid of supporting roller guard plate and mounting poldid of diagonaal traks pea.
4. Õigeaegne määrimine
määrimine sõitmine mehhanism on väga oluline. palju rull laagrid on 22 põlenud / 22 ja lammutatud sest õli leke. See on üldiselt arvestatud et seal võib olla õli leke sisse järgmine 5 kohad: õli leke kust väljast hoidmine rõngas to võlli tõttu to halb või kahjustatud O-rõngas vahel kinnitus rõngas ja võlli; õli leke vahel ja välimine kinnitusrõngas ja to rull due to halb kontakt of ujuv tihend rõngas või defekt of O-rõngas; leke vahel puks ja rull tõttu to poor O-rõngas vahel rull ja puks; õli leke toimub at õli täiteaine pistik due to lahti õli täiteaine pistik or kahjustatud ist auk of kooniline pistik tihend; Due to the poor O-ring, there is õli leke vahel the cover and the roller. Seega, pay attention to check the above parts at tavaline times, and and and replace them regular vastavalt to the määrimine tsükkel of iga osa.
5. Check for praod
Millal hooldamine buldooser, kontroll praod of reisimine mehhanism ajas, ja remont ja tugevdamine keevitus sisse ajas
Kuum tags: komatsu idler d155ax-3, Hiina, tarnijad, tootjad, tehas, osta
Küsi pakkumist
